Trilliant Cut Synthetic rutile: more fire in synthetic rutile than in diamond
Brilliance 65 · Fire 90 · Scintillation 79 · in our census, where the T73 scores 81 · 94 · 80 in synthetic rutile
How the Trilliant Cut handles light in synthetic rutile, measured: brilliance 65, fire 90 and 12% leakage, set against the T73 in the same stone and against the same cut in diamond.
Light Return map of the Trilliant Cut in synthetic rutile, face-up, from our own tracer at refractive index 2.616. Red, green and blue return light to the eye; gray leaks.
Trilliant Cut Synthetic rutile
Synthetic rutile has a refractive index of 2.616 to 2.903 and a dispersion of 0.330. Its critical angle, from the low end of that range, is 22.5°, so a round design needs a pavilion of at least 39.4° for head-on light to reflect off both sides of the pavilion and leave through the table. We trace it with one index, 2.760, the midpoint of the published range, and a fire spread of 0.284, 0.86 of the published dispersion. Every picture here is our Light Return tracer at 2.616, and every figure is from the same light census that scores the other gemstones; the 3D Gemstone Simulator shows the Trilliant Cut in synthetic rutile live. Synthetic rutile is strongly doubly refractive (birefringence 0.287): its two rays have critical angles of 22.5° and 20.1°. Our census traces one index, so every figure for it is a rough approximation.
The Trilliant Cut has 70 facets and a total depth of 58.9% of its width; its pavilion mains sit at 39.0°. In synthetic rutile, the census returns 65 of 100 for brilliance and 90 for fire, against 81 and 94 for the T73, our benchmark, in the same stone; the same Trilliant Cut in diamond reads 78 and 83.
Is synthetic rutile good in a Trilliant? Pros and cons, measured
Compared with the T73 Round Brilliant in synthetic rutile and with the Trilliant Cut in diamond.
A difference counts from 3 points (Brilliance, Fire, Tilt, Leakage), 5 (Scintillation,
Symmetry), 4% (face-up size per carat) or 5% (weight); Tilt counts as a pro only for a stone within
5 points of the brilliance it is compared with. How we measure.
All eight scores against the T73
At a glance: the Trilliant Cut in synthetic rutile (white) against the T73 Round Brilliant in synthetic rutile (dashed): solid white where
it reaches further, hatched where it falls short. Each pro and con is explained, with pictures, below.
Against the T73 Round Brilliant in synthetic rutile: ahead on 1, level on 1, behind on 6.
Global78, the comparison 88, difference −10
Brilliance65, the comparison 81, difference −16
Fire90, the comparison 94, difference −4
Scintillation79, the comparison 80, difference −1
Spread101, the comparison 100, difference +1
Symmetry62, the comparison 100, difference −38
Shape-norm76, the comparison 87, difference −11
Tilt94, the comparison 94, difference 0
Face-up light census, a different measure from the Cut Grading Tool; Spread and Shape-norm above 100 sit on the ring. Spread is the census's estimate from depth alone; the face-up size in the pros and cons is measured from each model's outline. Open it in the Cut Performance Wheel; these are the same census figures as our Cut Performance Index.
What the Trilliant Cut gains in synthetic rutile
More fire in synthetic rutile than in diamond
Fire 90 against 83 for the Trilliant Cut in diamond: 7 points higher
Fire is the share of the returned light that splits into color at the exit facet: the census traces each exit again at the refractive index minus and plus the fire spread (0.284 in synthetic rutile) and counts a ray as fire when the two directions differ by more than 0.6°. The Trilliant Cut reads 90 against 83 for the same cut in diamond. The figure is the census's; the 3D Gemstone Simulator renders synthetic rutile's fire live.
The fire figure is the census's, traced at the refractive index minus and plus the fire spread. See the fire in the 3D Gemstone Simulator: the Trilliant Cut in synthetic rutile under the sunny-day lighting.
What the Trilliant Cut gives up in synthetic rutile
A less regular pavilion than the T73
Symmetry 62 against 100 for the T73 Round Brilliant in synthetic rutile: 38 points lower
Symmetry reads how evenly the pavilion facets of each design family are cut: 100 − 6 × their scatter in degrees. The Trilliant Cut reads 62, the T73 100. It depends on the geometry alone, so it is the same in every stone.
Trilliant Cut · 70 facets · Symmetry 62
T73 Round Brilliant · 73 facets · Symmetry 100
Symmetry scores how regular the pavilion facets are within the design. Compare how evenly the facets repeat around each pavilion. Drawn from each cut's own model.
1.16 ct at 6.5 mm, against 0.96 ct for the same cut in diamond (+21%)
Weight follows specific gravity: 4.26 for synthetic rutile against 3.52 for diamond, so the same model at the same size weighs 1.16 ct here and 0.96 ct in diamond, 6.5 mm across. Nothing about the light changes with it.
A Trilliant Cut 6.5 mm across, weighed from the model's measured volume and each stone's specific gravity.
Returns less light than the T73 in synthetic rutile
Brilliance 65 against 81 for the T73 Round Brilliant in synthetic rutile: 16 points lower
Brilliance is the share of the 3,200 census rays that enter the stone and come back out of the crown towards the viewer. In synthetic rutile, whose critical angle is 22.5°, the Trilliant Cut returns 65 of 100 and the T73 81. The Trilliant Cut's pavilion mains sit at 39.0°, the T73's at 40.8°. The maps below show where each stone's light returns from and where it leaks.
Trilliant Cut in synthetic rutile · Brilliance 65
T73 Round Brilliant in synthetic rutile · Brilliance 81
Red, green and blue = light returning to the eye; gray = leakage, light that leaves heading down or stays inside. This is the head-on view; the Brilliance score averages a wider cone of light, so the score can differ from what one picture shows.
What helps:the DG-M5 reads 97 for brilliance in synthetic rutile, the best of the cuts we score there.
Face-up size 93 against 100 for the T73 Round Brilliant in synthetic rutile (T73 = 100): 7% less face-up area for the same weight
Face-up size is the outline's area per carat, measured from each model (T73 = 100): 93 for the Trilliant Cut against 100 for the T73. The same volume spread over a longer or shallower outline shows more face for the weight; it is the same in every stone, because specific gravity scales every cut alike.
Trilliant Cut · 6.19 mm at 1.00 ct · Face-up size 93
T73 Round Brilliant · 6.08 mm at 1.00 ct · Face-up size 100
Both stones weigh 1.00 ct in synthetic rutile and are drawn to the same scale in millimeters, from each cut's own model. Face-up size is the outline's area per carat, with the T73 at 100: a deeper stone, or a rounder outline, spreads less area for its weight.
What helps:the Marquise Cut reads 121 for face-up size in synthetic rutile, the best of the cuts we score there.
Our verdict on the Trilliant Cut in synthetic rutile
Pick the Trilliant Cut in synthetic rutile for this: it shows more fire than in diamond. The catch: it has a less regular pavilion than the T73, weighs more than in diamond, returns less light than the T73 and faces up smaller for its weight.
If that catch matters more to you, the DG-M5 reads 97 for brilliance in synthetic rutile, the best of the cuts we score there.
Every figure on this page is from our light census, traced at one refractive index: a simulation of the geometry, not a grading report. The 3D files and cutting files below are the same Trilliant Cut model we traced.
Trilliant Cut Synthetic rutile: questions
Is the Trilliant a good cut for synthetic rutile?
In our census the Trilliant Cut returns 65 of 100 for brilliance and 90 for fire in synthetic rutile, against 81 and 94 for the T73 in the same stone. Against that round and against the same cut in diamond it has 1 pro and 4 cons by our thresholds; the summary above names them.
What pavilion angle does synthetic rutile need?
At least 39.4° for a round design: synthetic rutile's critical angle is 22.5°, from the low end of its refractive index range, and head-on light has to reflect off both sides of the pavilion and leave through the table. The Trilliant Cut's pavilion mains sit at 39.0°.
How much does a Trilliant weigh in synthetic rutile?
At 6.5 mm across, 1.16 ct in synthetic rutile, against 0.96 ct for the same cut in diamond (+21%): synthetic rutile's specific gravity is 4.26, diamond's 3.52.
Can I see the Trilliant in synthetic rutile in 3D?
Yes: the 3D Gemstone Simulator renders it live, with synthetic rutile's own refractive index and dispersion. Synthetic rutile is traced by the same light census as the other gemstones, with its refractive index and fire spread derived from published values, so its scores are on the same scale; the pictures here are our Light Return tracer, and the Cut Performance Wheel sets it against any other cut and stone.
Get the Trilliant Cut files
6 formatsMillimetersWatertight
Trilliant Cut 3D files
The Trilliant Cut as exact geometry: 72 planar facets, real-world scale, ready for CAD,
rendering, printing and casting.
