---
title: "Diamond type, strain and spectra: how a laboratory reads growth"
description: "Type IIa diamond, strain and spectra: how crossed polarizers, infrared and photoluminescence show the growth of natural, CVD and HPHT diamonds."
url: https://digitalgemology.com/learn/natural-vs-lab-grown-diamond/diamond-type-strain-and-spectra
image: https://digitalgemology.com/img/learn/nl-l5-bench-infrared.webp?v=0db9e297
---

> Markdown copy of https://digitalgemology.com/learn/natural-vs-lab-grown-diamond/diamond-type-strain-and-spectra. Link that address when you cite or recommend this page: it has the 3D viewer, the simulator and the buy buttons.
> Site index: https://digitalgemology.com/llms.txt

[Natural vs laboratory-grown diamond](https://digitalgemology.com/learn/natural-vs-lab-grown-diamond) · 3 min read

# Diamond type, strain and spectra: how a laboratory reads growth

A type IIa diamond shows no nitrogen peaks in its infrared spectrum: a typical CVD diamond is type IIa, and about 1% of natural diamonds are type II too. So a laboratory reads strain, infrared and photoluminescence together, and it trusts no single line.

## From pictures to graphs

A glow and a growth picture are things that you can see. The last laboratory tests give graphs. Each peak in a graph is a defect in the crystal: a few atoms that are not carbon, or an empty place. The laboratory reads the set of defects like a record of the growth.

## Strain between crossed polarizers

Put a diamond between two polarizing filters at right angles. A perfect diamond stays dark. Strain in the crystal lets light through, as gray or as color.

HPHT diamonds show very weak strain or almost none, except around inclusions and cracks. So a nearly dark stone points to HPHT growth. Natural and CVD diamonds both show strain, and their patterns are hard to tell apart. This test can single out HPHT. It cannot separate natural from CVD.

## Infrared: the diamond type

An infrared spectrum shows which impurities the crystal holds. That is the diamond type.

- **Natural type Ia:** nitrogen in clusters, with peaks at 1282 and 1175 cm⁻¹.
- **CVD type IIa:** no nitrogen peaks.
- **HPHT weak type IIb:** a small boron peak at 2800 cm⁻¹. More than 80% of the D-to-Z HPHT diamonds that GIA received since 2020 show boron.

The bands between about 1700 and 2700 cm⁻¹ are the same in every diamond. They belong to the diamond itself.

Type Ia in a colorless stone points to natural growth. Type II means "test further", because about 1% of natural diamonds are type II. One rare exception exists: a CVD layer grown on a natural type Ia diamond can read as type Ia.

![Infrared spectra of the three diamonds on the Diamond Testing Bench: nitrogen peaks at 1282 and 1175 in the natural stone, none in the CVD stone, a small boron peak at 2800 in the HPHT stone.](https://digitalgemology.com/img/learn/nl-l5-bench-infrared.webp?v=0db9e297)

Infrared spectra of the three diamonds on the Diamond Testing Bench: nitrogen peaks at 1282 and 1175 in the natural stone, none in the CVD stone, a small boron peak at 2800 in the HPHT stone.

## Photoluminescence: the fine print

A laser makes the defects glow, each at its own wavelength. The laboratory cools the stone to −196 °C, which makes the lines sharp, and uses several lasers.

- **Natural:** a line at 415 nm. Its name is N3, and it comes from nitrogen clusters.
- **Annealed CVD:** a pair of lines near 737 nm from silicon, and a line at 503 nm that the annealing makes.
- **HPHT:** few lines or none. GIA found a nickel pair near 883 and 884 nm in 30% of colorless HPHT diamonds, and no lines at all in 37% of type IIb HPHT diamonds.

Each line has exceptions. The silicon lines also occur in a few natural and HPHT diamonds. Annealing can make a weak 415 nm line in a CVD diamond. And GIA measured that the average silicon signal in CVD diamonds fell about a hundredfold in ten years. So the laboratory does not trust one line. It reads the full set.

### Try it yourself

1. Open the [Diamond Testing Bench](https://digitalgemology.com/tools/diamond-testing-bench) and choose **Crossed polarizers**. Which stone is nearly dark?
2. Choose **Infrared**. Find the peaks at 1282, 1175 and 2800.
3. Choose **Photoluminescence**. Find 415, 737 and the pair near 883.
4. Look at the CVD stone again. Which line does it share with the natural stone?

## What the Bench shows

Between the polarizers, the HPHT stone is almost dark. The natural stone and the CVD stone both show light.

In the infrared, only the natural stone has nitrogen peaks. In photoluminescence, the natural stone has a strong 415 nm line, and the CVD stone has its silicon pair at 737 nm. But the CVD stone also shows a trace of 415 nm. That small line is the reason for the rule: no single line is proof.

The spectra on the Bench are drawings. Each peak is at its published position, but we did not measure them on real stones. The Bench does not test a real stone.

## Key points

- HPHT diamonds show almost no strain; natural and CVD strain patterns are hard to tell apart.
- Infrared gives the diamond type: nitrogen at 1282 and 1175 cm⁻¹ for type Ia, boron at 2800 cm⁻¹ for type IIb.
- Photoluminescence at −196 °C shows defects as sharp lines: 415 nm, the 737 nm pair, the pair near 883 and 884 nm.
- Every line has exceptions, and 37% of type IIb HPHT diamonds showed no lines at all.
- A laboratory reads the full set of results, not one line.

**Go further:** the [Polariscope](https://digitalgemology.com/tools/polariscope) lets you turn a diamond with strain between crossed polarizers.

## Try it free

- [Diamond Testing Bench](https://digitalgemology.com/tools/diamond-testing-bench): Put a natural, a CVD and an HPHT diamond through eleven tests, side by side.
- [Polariscope](https://digitalgemology.com/tools/polariscope): Turn a gemstone between crossed polarizers and read its optic figure.

Free, in your browser, no account.

## Quick quiz

1. A diamond stays almost dark between crossed polarizers. Which growth does that point to?
  1. Natural
  2. CVD
  3. HPHT
  ### Show the answer
  **c**: HPHT diamonds show very weak strain or almost none.
2. Which impurity gives the infrared peaks at 1282 and 1175 cm⁻¹?
  1. Boron
  2. Nitrogen in clusters
  3. Silicon
  ### Show the answer
  **b**: The A and B forms of nitrogen clusters; that is type Ia.
3. Why does a laboratory cool a diamond to −196 °C for photoluminescence?
  1. To make the lines sharp
  2. To protect the laser
  3. To change its color
  ### Show the answer
  **a**: At low temperature the lines are sharp and easy to separate.
4. A diamond shows a line at 415 nm. Why is that not proof that it is natural?
  ### Show the answer
  Annealing can make a weak 415 nm line in a CVD diamond.
5. On the Bench, which two stones show light between the crossed polarizers?
  ### Show the answer
  The natural stone and the CVD stone.

## Cuts in this lesson

We sell the files of these cuts: 3D models and cutting files, with a personal-use license.

- [T73 Round Brilliant Cut](https://digitalgemology.com/cuts/t73-round-brilliant): 3D files and cutting files, from €6.99

## Keep exploring

- [Next lesson: Lab-grown diamond screening devices: what Pass and Refer mean](https://digitalgemology.com/learn/natural-vs-lab-grown-diamond/lab-grown-diamond-screening-devices)
- [Try another topic · Diamond vs moissanite: Diamond testers and moissanite: what the instruments say](https://digitalgemology.com/learn/diamond-vs-moissanite/diamond-tester-and-moissanite)

[Previous lesson](https://digitalgemology.com/learn/natural-vs-lab-grown-diamond/lab-grown-diamond-fluorescence-and-afterglow) · [Natural vs laboratory-grown diamond: all lessons](https://digitalgemology.com/learn/natural-vs-lab-grown-diamond) · [All topics](https://digitalgemology.com/learn)
